Hire an Expert : 0086-371-86151927

call us

0086-371-86151927

s50c c48 material property

s50c c48 material property

s50c c48 material property Related Products

  • S50C BEBON steel

    JIS G4051 S50C steel plate is one mainly of high carbon steel,for the high strength medium carbon steel,the cold work plasticity is low,the welding performance,the hardenability are bad,but non temper brittleness,cutting value still permissible.Generally under the normalizing or quenching,the tempering uses,uses in making the resistance to wear

  • S50C (JIS ) Worldwide equivalent grades

    S50C (Japan, JIS ) European (EU, EN) and wordwide Steel equivalent grades These comparison table is only intended as an indication of the closest khown equivalent grades. The source standarts should always be checked for the specific purpose for each material, in case of doubt Buy, sell, suppliers search product S50C on line

  • C45 / 1.0503 SteelNumber Chemical composition

    Properties of steel C45 (1.0503) WeldabilityDue to the medium high carbon content it can be welded with some precautions. HardenabilityIt has a low hardenability in water or oil; fit for surface hardening that gives this steel grade a high hardness of the hardened shell. Equivalent grades of steel C45 (1.0503

  • Carbon Steel S50C/SS400

    Carbon Steel S50C / SS400 S50C S50c is in category of medium carbon which is widespread use in basic task , structural , agricultural , machinery equipment as well as mold. Also, widely used in engine part. Thanks to its various good properties such as strength , tensile, cheap. Moreover, it also can quench to enchance its strength.

  • JIS S45C Mild Steel An Overview

    S45C is a medium strength steel. Suitable for shafts studs, keys etc. Available as rolled or normalised. Supplied as square bar, or round bar or flat.

  • S55C steel

    The material does not have direct Metallography properties. Directory is being updated. The material does not have direct Metallography properties. Directory is being updated. Contact Suppliers with your enquiries for S55C any of the shape and size. Tool & Die Steels Inc. Stainless Steel, Special Steel, Compressor Blading, Turbine Blading

  • If you need precision metal materials, you need Tokushu

    Carbon tool steels (SK2, SK4, SK5, SK6, and SK7) are the most widely used cold rolled special steel strips due to their workability, hardenability, product performance, affordability, and other characteristics. These steels acquire high hardness when quenched, and are therefore suited for use in blades, knitting needles, spiral springs, leaf springs, and other applications requiring properties

  • ASTM G48 11(2015) Standard Test Methods for Pitting and

    4.2 The use of ferric chloride solutions is justified because it is related to, but not the same as, that within a pit or crevice site on a ferrous alloy in chloride bearing environments (1, 2). 4 The presence of an inert crevice former of consistent dimension on a surface is regarded as sufficient specification of crevice geometry to assess relative crevice corrosion susceptibility.

  • SAE AISI 1045 (S45C, G10450) Carbon Steel :MakeItFrom

    The graph bars on the material properties cards further below compare SAE AISI 1045 steel towrought carbon or non alloy steels (top), all iron alloys (middle), and the entire database (bottom). A full bar means this is the highest value in the relevant set. A half full

  • JIS G4051 Grade S50C Medium Carbon Steel Matmatch

    See the chemical composition and physical properties of JIS G4051 Grade S50C , find alternative materials, and connect with suppliers.

  • AISI 1050 Carbon Steel (UNS G10500) Materials

    Physical Properties Mechanical Properties Thermal Properties Other Designations Introduction. Carbon steels contain carbon as the main alloying element. They are designated by AISI four digit numbers, and contain 0.4% of silicon and 1.2% of manganese. Molybdenum, chromium, nickel, copper, and aluminium are present in small quantities.

  • If you need precision metal materials, you need Tokushu

    Carbon tool steels (SK2, SK4, SK5, SK6, and SK7) are the most widely used cold rolled special steel strips due to their workability, hardenability, product performance, affordability, and other characteristics. These steels acquire high hardness when quenched, and are therefore suited for use in blades, knitting needles, spiral springs, leaf springs, and other applications requiring properties

  • 321 Stainless Steel Technical Data Sheet

    Type 321 stainless steel s also advantageous for high temperature service because of its good mechanical properties. Type 321 stainless steel offers higher creep and stress rupture properties than Type 304 and, particularly, Type 304L which might also be considered for exposures where sensitization and intergranular corrosion are concerns.

  • Steel grades The Tool Hub

    Good through hardening properties especially for large molds, excellent resistance to thermal shock and to thermal fatigue, good resistance to heat erosion. AL, Mg Die casting molds, Parts for die casting molds, AL die extrusion molds, Hard plastics molds.

  • 17 7 Alloy, 17 7 Stainless Steel, 17 7 Sheet, 17 7 Plate

    * All Trademarks and/or Trade names are the properties of their respective owners. 17 7 Stainless Steel Data Sheet (view complete data sheet for this material including material property data, metal compositions, etc) California Metal & Supply is a leading supplier of quality

Our advantage:
· 20 Years of experience in the Steel field
· 500,000 MT production capacity per year.
· 100+ exporting markets covering global main countries and regions.
· 2000+ MT stock per month with different materials and sizes.
· 150+ projects each year, covering oil tank, shipbuilding, oil&gas pipeline, drilling, offshore, energy, construction industries.

Our Steel Products' Certificates:

Package: